Blechbearbeitungszentrum ЛИНИЯ ПРОДОЛЬНОЙ РЕЗКИ МЕТАЛЛА Китай, B.j. 2018

LONGITUDINAL METAL CUTTING LINE 193781 €


Technical characteristics
The line is designed for longitudinal and transverse cutting of sheet metal, special steel sheet with a thickness of 0.5 mm, winding and unloading of a roll of gauge metal in automatic mode. The main characteristics of the line are shown in Table 1.1.
Table 1.1 - Main characteristics of the line
Technical characteristics of the line Dimensional characteristics
Overall dimensions (length x width x height, mm) 21117 x 8612 x 2700
Rated supply voltage, V 380 (three-phase, variable)
Frequency, Hz 50...60
Ready time of the line, after switching on the GHS, min. 5...10
Line capacity, units/hour
Number of GFS, pcs. 1
Method of controlling the LPG Control panel
Oil volume of the hydraulic shearing unit, l 560
Hydraulic shears for transverse sheet cutting, pcs. 1
Device for longitudinal sheet cutting, pcs. 1
Temperature mode of line operation, ºС +5...+50
Working pressure in pneumatic lines, MPa 0,5...0,6
Working pressure in hydraulic lines, MPa 14...16
Cooling of hydraulic lines Airborne
Type of line Stationary
Type of control of main technological parameters Automatic
Method of controlling the main technological parameters Control panel
Compressed air for pneumatic systems With 40 micron filtration with or without oil
Mineral hydraulic oil for GHS MGE-46V
Mineral oil viscosity, cSt 40...50
Oil purity class according to GOST 17216-81 not coarser than 12
Presence of water and acids in the oil Absence of
Filtration of oil before pouring into the tank Particles with a diameter of more than 0.025...0.04 mm
Oil temperature during operation, ºС +10...+50
Temperature regime of compressed air during operation, ºС +5...+50
Number of operating personnel, persons / shift 2
Dimensional accuracy when cutting sheet metal, mm ±1

Composition of the line
The line is built on a modular basis. The line is used for longitudinal and transverse cutting of sheet metal, coiling and unloading of a roll of measuring metal in automatic mode.
The line includes (Fig. 1.1):
- cantilever unwinder of coiled metal (strip) pos.1 with hydraulic coil unwinding device and loading device (trolley)
- drawing device item 2;
- drive of the broaching device item 3;
- hydraulic scissors for transverse cutting of metal item 4;
- hydraulic table with conveyor rollers and loop compensator item 5;
- guide device for sheet metal item 6;
- longitudinal cutting station for metal item 7;
- drive of the station for longitudinal cutting of metal item 8;
- sheet metal cleaning device item 9;
- hydraulic table with conveyor rollers and loop compensator item 10;
- device for reeling in waste metal (edge reeler), item 11 (left and right);
- tensioning station with separating disks Poz.12;
- cantilever coiler of coiled metal (strip), item 13 with hydraulic coil unclamping device, separating disks and unloading device (trolley);
- drive of the cantilever coil winder of coiled metal Item 14;
- Hydraulic oil compressor, with air cooling of working fluid, item 15;
- control panel item 16.






















Figure 1.1 - Composition of a longitudinal sheet metal cutting line: 1 - cantilever unwinder of coiled metal (strip); 2 - broaching device; 3 - drive of the broaching device; 4 - hydraulic scissors for transverse cutting of metal; 5 - hydraulic table with conveyor rollers and loop compensator; 6 - guide device for sheet metal; 7 - longitudinal cutting station; 8 - drive of the longitudinal cutting station; 9 - sheet metal cleaning device; 10 - hydraulic table with conveyor rollers and loop compensator; 11 - waste coiler (edge coiler) for sheet metal; 12 - tensioning station with separating discs; 13 - cantilever coiler of coiled metal (strip); 14 - drive of the cantilever coiler of coiled metal; 15 - gas station; 16 - control panel